Ubus¶

The Network Characterization daemon (NCd) uses Ubus (the OpenWrt micro bus architecture) to communicate with the Network Characterization user interface and with other daemons and applications. This page documents the ubus namespace of the NC, with the available procedures and several examples.

The NCd can provide information about the local node or about remote nodes. Some of the data are specific to the NCd, while others can be obtained from other local Ubus interfaces (netifd, rpcd, etc.). The NCd acts as a relay to the local Ubus, but also to remote Ubus instances. By doing so, most of the data processing is left on the NCui side, which is run on Javascript code by the user's browser. This strategy reduces the load on the network nodes, usually low-end embedded devices with limited memory and processing resources.

NCd ubus namespace and procedures summary¶

The NCd, once registered to the Ubus daemon, provides the following procedures:

Local node ID¶

Each node running the NC has its unique ID that identifies it on the network.

Path	Procedure	Signature	Description
ncd	local	{ }	Get the unique id of the local node

 

List all nodes¶

List all the known or discovered nodes in the network.

Path	Procedure	Signature	Description
ncd	listnodes	{ }	Get a list with all the nodes in the network

 

Neighbour nodes list¶

List the neighbours of the local node (i.e.: directly connected either via wire or wireless).

Path	Procedure	Signature	Description
ncd	neighbours	{ }	Get a list with the neighbours of the local node

 

NCd-specific information¶

Path	Procedure	Signature	Description
ncd	version	{ }	Get the version of the NCd

 

NC-specific node information¶

The NCd can provide the following procedures regarding other nodes in the network running the NCd:

Path	Procedure	Signature	Description
ncd.nodeid.location.name	get	{ }	Get the position (name or description) where the node defined by nodeid is located
ncd.nodeid.location.name	get	{ "location" : "Location name or description" }	Get the position (name or description) where the node defined by nodeid is located
ncd.nodeid.location.coordinates	get	{ }	Get the position (latitude and longitude coordinates) where the node defined by nodeid is located
ncd.nodeid.location.coordinates	set	{ "coordinates" : [ "lat", "lon" ] }	Set the position (latitude and longitude coordinates) where the node defined by nodeid is located

² Replace nodeid by the node's unique id or by local to request information about the local node
 

Ubus relay via NC¶

The NCd is able to relay Ubus calls from the NCui to other Ubus instances registered remotely (like netifd, rpcd, etc.).

Path	Procedure	Signature	Description
ncd.nodeid.relay.daemon.path ²	procedure	{ "daemon.path procedure signature" }	Get the unique id of the node defined by nodeid

² Replace nodeid by the node's unique id
 

See the examples below to get a clear idea of how it works.

Usage examples¶

ncd local id¶

Request:

ubus call ncd local { }

Response:

{ "id" : "node016" }

 

ncd listnodes¶

Request:

ubus call ncd listnodes { }

Response:

{ "nodes" : [ "node011", "node016", "node400", "node094", "node017", "node104", "node105", "node106", "node107" ] }

 

ncd neighbours¶

Request:

ubus call ncd neighbours { }

Response:

{ "nodes" : [ "node011", "node400" ] }

 

ncd local node neighbours¶

Request:

ubus call ncd.local neighbours { }

or, equivalently if the local node's unique id is "node016":

ubus call ncd.node016 neighbours { }

Response:

{ "nodes" : [ "node011", "node400" ] }

 

ncd remote node neighbours¶

Request:

ubus call ncd.node011 neighbours { }

Response:

{ "nodes" : [ "node094", "node400" ] }

 

ncd local node link devices¶

Request:

ubus call ncd.local linkdevices { "nodes" : [ "node011", "node400" ] }

or, equivalently if the local node's unique id is "node016":

ubus call ncd.node016 linkdevices { "nodes" : [ "node011", "node400" ] }

Response:

{
  "links": [
    {
      "node011": [
        "eth0.12",
        "wlan0" 
      ]
    },
    {
      "node400": [
        "wlan0" 
      ]
    }
  ]
}

 

ncd remote node link devices¶

Request:

ubus call ncd.node011 linkdevices { "nodes" : [ "node016", "node094", "node400" ] }

Response:

{
  "links": [
    {
      "node016": [
        "wlan0" 
      ]
    },
    {
      "node094": [
        "wlan1" 
      ]
    },
    {
      "node400": [
        "wlan0",
        "wlan1" 
      ]
    }
  ]
}

 

ncd local location name get¶

Request:

ubus call ncd.local.location.name get { }

or, equivalently if the local node's unique id is "node016":

ubus call ncd.node016.location.name get { }

Response:

{ "name" : [ "Narrow Street 16, Faketown" ] }

 

ncd local position name set¶

Request:

ubus call ncd.local.location.name set { "name" : [ "Narrow Street 16, Faketown (rooftop)" }

or, equivalently if the local node's unique id is "node016":

ubus call ncd.node016.location.name set { "name" : [ "Narrow Street 16, Faketown (rooftop)" }

Response:

{ ] }

 

ncd local position coordinates get¶

Request:

ubus call ncd.local.location.coordinates get { }

or, equivalently if the local node's unique id is "node016":

ubus call ncd.node016.location.coordinates get { }

Response:

{ "coordinates" : [ "42.34796", "3.11036" ] }

 

ncd local position coordinates set¶

Request:

ubus call ncd.local.position.coordinates set { "coordinates" : [ "43.34796", "4.11036" ] }

or, equivalently if the local node's unique id is "node016":

ubus call ncd.node016.position.coordinates set { "coordinates" : [ "43.34796", "4.11036" ] }

Response:

{ }

 

ncd local ubus relay¶

Request:

ubus call ncd.local.relay.iwinfo devices { }

Response:

{
    "devices": [
        "wlan1",
        "wlan0",
        "wlan0ap" 
    ]
}
 

 

ubus call iwinfo devices

More examples¶

There is an example of the communication process between the CNAd and the CNAui via ubus here.