Projecte

General

Perfil

Config » Historial » Revisió 5

Revisió 4 (Pau Escrich, 09-01-2013 17:36) → Revisió 5/13 (Pau Escrich, 09-01-2013 17:38)

h1. Config 

 <pre> 
 config 'qmp' 'interfaces' 
 #         option 'configure_switch' 'eth0'                      # (uncomment line if available, e.g. WGT634U) 
         option 'lan_devices'        'eth0 wlan1 dummy0'         # LAN (dhcp server) 
         option 'wan_devices'        'eth1'                      # WAN (dhcp client) 
         option 'mesh_devices'       'wlan0 wlan2 eth0 eth1'     # Mesh devices, will be extended by VLAN tag! 
         option 'no_vlan_devices'     ''                         # Network devices where we do not want to use VLAN tag (not recommended!) 

 config 'qmp' 'node' 
	 option 'primary_device' 'eth0' 
	 option 'community_id' 'qMp' 
	 option 'community_node_id' '' 
	 option 'key' '/tmp/qmp_key' 

 # Update firmware server 
 config 'qmp' 'update' 
	 option 'url' 'http://fw.qmp.cat/testing' 
	 option 'images' 'IMAGES' 
	 option 'devices' 'DEVICES' 
	 option 'filter' 'sysupgrade' 
	 option 'preserve' '/etc/config/qmp /etc/shadow /etc/passwd /etc/rc.local /etc/firewall.user /etc/dropbear/* /etc/config/b6m-spread' 

 # This is for Roaming mode, each mode 
 # Each node assings a non-overlapping DHCP IPv4 ranges over a /16 network on LAN device 
 config 'qmp' 'non_overlapping' 
         option 'ignore'                '0'   
         option 'dhcp_offset'           '2' 
         option 'qmp_leasetime'         '1h' 

 config 'qmp' 'networks' 
         option 'dns'                   '141.1.1.1 85.126.4.170 202.83.95.227' 
         option 'lan_address'           '172.30.22.1' 
         option 'lan_netmask'           '255.255.255.0' 

         # means olsr6 use vlantag 10+1, bmx6 use vlantag 10+2 
         option 'mesh_protocol_vids'    'olsr6:1 bmx6:2'    
         option 'mesh_vid_offset'       '10' 

         # rescue network prefix, the 16 missing bits are taken from device MAC  
	 option 'rescue_prefix24'       '169.254'  

         # OLSR (backup protocol) only supports IPv6 
         option 'olsr6_mesh_prefix48' 'fd01:0:0' 
         option 'olsr6_ripe_prefix48' '2011:0:0' 

         # BMX6 (main protocol) runs IPv6 backbone and IPv4 tunneled 
         option 'bmx6_mesh_prefix48'    'fd02:0:0' 
         option 'bmx6_ripe_prefix48'    '2012:0:0'          # suffix is autoconfigured based on community_node_id 
         option 'bmx6_ipv4_prefix24'    '10.202' 
 #         option 'bmx6_ipv4_address'     '10.202.9.01/24'    # if commented out then option is autoconfigured based on 
                                                        # community_node_id and bmx6_ipv4_prefix 
	 option 'bmx6_tablePrefTuns'    '7000' 
	 option 'bmx6_tableTuns'        '70' 
	 option 'bmx6_throwRules'       '1' 

         option 'babel_mesh_prefix48' 'fd03:0:0' 
	 option 'netserver' '1' 

 config 'qmp' 'tunnels' 
         option 'search_ipv4_tunnel'    '0.0.0.0/0' 
         option 'search_ipv6_tunnel'    '::/0' 
 #         option 'offer_ipv4_tunnel'    '0.0.0.0/0' 
 #         option 'offer_ipv6_tunnel'    '::/0' 


 config 'qmp' 'wireless' 
         option 'driver'    'mac80211' 
         option 'country' 'SP' 
         option 'bssid'     '02:CA:FF:EE:BA:BE' 
 config 'qmp' 'interfaces' 
 #         option 'configure_switch' 'eth0'                      # (uncomment line if available, e.g. WGT634U) 
         option 'lan_devices'        'eth0 wlan1 dummy0'         # will be used as is! 
         option 'wan_devices'        'eth1'                      # will be used as is! 
         option 'mesh_devices'       'wlan0 wlan2 eth0 eth1'     # will be extended by vlan tag! 

 config 'qmp' 'node' 
	 option 'primary_device' 'eth0' 
	 option 'community_id' 'qMp' 
	 option 'community_node_id' '' 
	 option 'key' '/tmp/qmp_key' 

 config 'qmp' 'update' 
	 option 'url' 'http://fw.qmp.cat/testing' 
	 option 'images' 'IMAGES' 
	 option 'devices' 'DEVICES' 
	 option 'filter' 'sysupgrade' 
	 option 'preserve' '/etc/config/qmp /etc/shadow /etc/passwd /etc/rc.local /etc/firewall.user /etc/dropbear/* /etc/config/b6m-spread' 

 config 'qmp' 'non_overlapping' 
         option 'ignore'                '0'    # Each node assings a non-overlapping DHCP IPv4 ranges over a /16 network on lan device 
         option 'dhcp_offset'           '2' 
         option 'qmp_leasetime'         '1h' 

 config 'qmp' 'networks' 
         option 'dns'                   '141.1.1.1 85.126.4.170 202.83.95.227' 
         option 'lan_address'           '172.30.22.1' 
         option 'lan_netmask'           '255.255.255.0' 
         #option 'publish_lan' 	      '0' 
	 #option 'niit_prefix96'         '0:0:0:0:0:ffff'          # omit trailing 32 ipv4 bits ! 
         option 'mesh_protocol_vids'    'olsr6:1 bmx6:2'     # means olsr6 use vlantag 10+1, bmx6 use vlantag 10+2 
         option 'mesh_vid_offset'       '10' 

	 option 'rescue_prefix24'       '169.254' # rescue network prefix, the 16 missing bits are taken from device MAC  

         option 'olsr6_mesh_prefix48' 'fd01:0:0' 
         option 'olsr6_ripe_prefix48' '2011:0:0' 
         option 'olsr6_ipv4_prefix24' '10.201' 
 #         option 'olsr6_ipv4_address'    '10.201.9.01' 
 #         option 'olsr6_ipv4_netmask'    '255.255.255.0' 
 #         option 'olsr6_6to4_netmask'    '120' 

         option 'bmx6_mesh_prefix48'    'fd02:0:0' 
         option 'bmx6_ripe_prefix48'    '2012:0:0'          # suffix is autoconfigured based on community_node_id 
         option 'bmx6_ipv4_prefix24'    '10.202' 
 #         option 'bmx6_ipv4_address'     '10.202.9.01/24'    # if commented out then option is autoconfigured based on 
                                                        # community_node_id and bmx6_ipv4_prefix 
	 option 'bmx6_tablePrefTuns'    '7000' 
	 option 'bmx6_tableTuns'        '70' 
	 option 'bmx6_throwRules'       '1' 

         option 'babel_mesh_prefix48' 'fd03:0:0' 
	 option 'netserver' '1' 

 config 'qmp' 'tunnels' 
         option 'search_ipv4_tunnel'    '0.0.0.0/0' 
         option 'search_ipv6_tunnel'    '::/0' 
 #         option 'offer_ipv4_tunnel'    '0.0.0.0/0' 
 #         option 'offer_ipv6_tunnel'    '::/0' 


 config 'qmp' 'wireless' 
         option 'driver'    'mac80211' 
         option 'country' 'SP' 
         option 'bssid'     '02:CA:FF:EE:BA:BE' 

 config 'qmp' 'interfaces' 
 #         option 'configure_switch' 'eth0'                      # (uncomment line if available, e.g. WGT634U) 
         option 'lan_devices'        'eth0 wlan1 dummy0'         # will be used as is! 
         option 'wan_devices'        'eth1'                      # will be used as is! 
         option 'mesh_devices'       'wlan0 wlan2 eth0 eth1'     # will be extended by vlan tag! 

 config 'qmp' 'node' 
	 option 'primary_device' 'eth0' 
	 option 'community_id' 'qMp' 
	 option 'community_node_id' '' 
	 option 'key' '/tmp/qmp_key' 

 config 'qmp' 'update' 
	 option 'url' 'http://fw.qmp.cat/testing' 
	 option 'images' 'IMAGES' 
	 option 'devices' 'DEVICES' 
	 option 'filter' 'sysupgrade' 
	 option 'preserve' '/etc/config/qmp /etc/shadow /etc/passwd /etc/rc.local /etc/firewall.user /etc/dropbear/* /etc/config/b6m-spread' 

 config 'qmp' 'non_overlapping' 
         option 'ignore'                '0'    # Each node assings a non-overlapping DHCP IPv4 ranges over a /16 network on lan device 
         option 'dhcp_offset'           '2' 
         option 'qmp_leasetime'         '1h' 

 config 'qmp' 'networks' 
         option 'dns'                   '141.1.1.1 85.126.4.170 202.83.95.227' 
         option 'lan_address'           '172.30.22.1' 
         option 'lan_netmask'           '255.255.255.0' 
         #option 'publish_lan' 	      '0' 
	 #option 'niit_prefix96'         '0:0:0:0:0:ffff'          # omit trailing 32 ipv4 bits ! 
         option 'mesh_protocol_vids'    'olsr6:1 bmx6:2'     # means olsr6 use vlantag 10+1, bmx6 use vlantag 10+2 
         option 'mesh_vid_offset'       '10' 

	 option 'rescue_prefix24'       '169.254' # rescue network prefix, the 16 missing bits are taken from device MAC  

         option 'olsr6_mesh_prefix48' 'fd01:0:0' 
         option 'olsr6_ripe_prefix48' '2011:0:0' 
         option 'olsr6_ipv4_prefix24' '10.201' 
 #         option 'olsr6_ipv4_address'    '10.201.9.01' 
 #         option 'olsr6_ipv4_netmask'    '255.255.255.0' 
 #         option 'olsr6_6to4_netmask'    '120' 

         option 'bmx6_mesh_prefix48'    'fd02:0:0' 
         option 'bmx6_ripe_prefix48'    '2012:0:0'          # suffix is autoconfigured based on community_node_id 
         option 'bmx6_ipv4_prefix24'    '10.202' 
 #         option 'bmx6_ipv4_address'     '10.202.9.01/24'    # if commented out then option is autoconfigured based on 
                                                        # community_node_id and bmx6_ipv4_prefix 
	 option 'bmx6_tablePrefTuns'    '7000' 
	 option 'bmx6_tableTuns'        '70' 
	 option 'bmx6_throwRules'       '1' 

         option 'babel_mesh_prefix48' 'fd03:0:0' 
	 option 'netserver' '1' 

 # Offer/Fetch networks in the Mesh 
 config 'qmp' 'tunnels' 
         option 'search_ipv4_tunnel'    '0.0.0.0/0' 
         option 'search_ipv6_tunnel'    '::/0' 
 #         option 'offer_ipv4_tunnel'    '0.0.0.0/0' 
 #         option 'offer_ipv6_tunnel'    '::/0' 


 # Main wireless configuration (common for all wifi devices) 
 config 'qmp' 'wireless' 
         option 'driver'    'mac80211' 
         option 'country' 'SP' 
         option 'bssid'     '02:CA:FF:EE:BA:BE' 

 # First wifi device 
 config 'wireless' 
	 option 'mode' 'adhoc' 
	 option 'name' 'qMp.lab104' 
	 option 'txpower' '14' 
	 option 'channel' '140-' 
	 option 'mac' '90:a4:de:c0:bb:c3' 
	 option 'device' 'wlan0' 

 # Second wifi device 
 config 'wireless' 
	 option 'mode' 'ap' 
	 option 'name' 'qMp' 
	 option 'txpower' '17' 
	 option 'channel' '9+' 
	 option 'mac' '00:80:48:78:75:23' 
	 option 'device' 'wlan1' 

 </pre>