Wireless autoconf » Historial » Revisió 9
Revisió 8 (Pau Escrich, 13-06-2011 18:01) → Revisió 9/15 (Pau Escrich, 13-06-2011 18:18)
h1. Wireless autoconf h2. Technical information (for developers) This is the wireless configuration for file: /etc/config/qmp These are the default parameters sharing all wireless interfaces <pre> config 'qmp' 'wireless' option 'driver' 'mac80211' option 'country' 'UZ' option 'bssid' '02:CA:FF:EE:BA:BE' </pre> driver can be `mac80211` for athXk, and `madwifi` for madwifi And these are the config parameters for each wifi interface. <pre> config 'wireless' option 'channel' '44' option 'mode' 'adhoc' option 'name' 'qmp' option 'mac' '00:80:48:6b:25:b5' config 'wireless' option 'channel' '10' option 'mode' 'ap' option 'name' 'qmp.cat-AP' option 'mac' '00:80:48:6b:25:b6' </pre> h3. qmp_wireless_config To apply this configuration to device, you must execute this commands: <pre> . /etc/qmp/qmp_wireless.sh qmp_configure_wifi </pre> This function takes the parameters from UCI and using the templates from: /etc/qmp/templates creates the openwrt wireless config Templates are named like that: wireless.mac80211.adhoc wireless.madwifi.ap Separed by dots, second name is the driver to use and third one is the mode. These templates looks like this: <pre> config wifi-device #QMP_DEVICE option type mac80211 option macaddr #QMP_MAC option channel #QMP_CHANNEL option diversity 0 # 0:off, 1:on option txantenna 0 # 0:auto, 1:main, 2:aux option rxantenna 0 # 0:auto, 1:main, 2:aux option country #QMP_COUNTRY option outdoor 1 # option txpower 1 config wifi-iface option device #QMP_DEVICE option mode adhoc option ssid #QMP_SSID option bssid #QMP_BSSID option encryption none </pre> As you can see, the special words starting witch #QMP will be replaced by UCI parameters. So you can play a little with templates. For example, there is a template named: `wireless.mac80211.adhoc-n` But the function qmp_wireless_config requires a complete configuration from UCI. So there is another function to generate the UCI config. h3. qmp_wireless_config_initial To execute this function: <pre> . /etc/qmp/qmp_wireless.sh qmp_configure_wifi_initial </pre> This generates de UCI qmp configuration, but not allways from zero. You can have some parameters configured and the function will configure the rest for you. For example, you can have a configuration like this: <pre> config 'wireless' option 'channel' '132' option 'mode' 'adhoc' </pre> And after execute qmp_configure_wifi_initial you will have the rest of needed parameters <pre> config 'wireless' option 'channel' '132' option 'mode' 'adhoc' option 'name' 'qmp' option 'mac' '00:80:48:6b:25:b5' </pre> So, if you want to use the first device for meshing and the second one for access point, you can build the openwrt image with this kind of configuration: <pre> config 'wireless' option 'mode' 'adhoc' config 'wireless' option 'mode' 'ap' </pre> And after the first startup qmp_configure_wifi_initial will be executed putting the rest of parameters. The default configuration is read from file: /etc/qmp/templates/wireless.default.config looks like that: <pre> driver mac80211 country UZ bssid 02:CA:FF:EE:BA:BE channel 44 mode adhoc name qmp.cat </pre>